Металеві алюмінієві сплави

Що таке металеві алюмінієві сплави?

Алюміній є одним з легких металевих матеріалів з додаванням певної кількості інших легуючих елементів. Крім загальних характеристик алюмінію, алюмінієві сплави мають деякі специфічні характеристики сплавів через різні типи та кількість доданих легуючих елементів. The density of aluminum alloy is 2.63～2.85g/cm, with high strength (σb is 110～650MPa), the specific strength is close to high alloy steel, the specific stiffness exceeds steel, with good casting performance and plastic processing performance, хороша електро- і теплопровідність, хороша стійкість до корозії та зварюваність, can be used as structural materials, in aerospace, авіації, транспортування, будівництво, mechanical and electrical, light chemical and It have a wide range of applications in aerospace, авіації, транспортування, будівництво, electromechanical, light chemical and daily necessities.

What are some common alloys of aluminum?

Metal aluminum alloy is a general term for alloys based on aluminum. There are different models, and the metal components added to various aluminum alloys are also different. The main alloying elements are Cu(мідь), І(кремній), Mg(магній), Zn(цинк), Мн( марганець), and the secondary alloying elements are Ni(нікель),Fe( залізо), з(титан), кр(хром), Li(літій), etc.According to the alloy series, її можна розділити на:

Metal aluminum alloy series

• 1000 серія чистий алюміній
• 2000 серія металевий алюмінієвий сплав
• 3000 серія металевий алюмінієвий сплав
• 4000 серія металевий алюмінієвий сплав
• 5000 серія металевий алюмінієвий сплав
• 6000 серія металевий алюмінієвий сплав
• 7000 серія металевий алюмінієвий сплав
• 8000 серія металевий алюмінієвий сплав

Metal aluminum alloy raw materials are divided into

Hot selling metal aluminum alloys

1xxx series metal aluminum alloys

1серія xxx:: 1050, 1060, 1070, 1100, 1200, 1235 тощо

3серія xxx: 3003, 3004, 3005, 3104, 3105 тощо

5серія xxx: 5005, 5052, 5083, 5086, 5454, 5754 тощо

6серія xxx: 6061, 6063, 6082 тощо

Hot selling metal aluminum alloys tempers

According to temper, it can be divided into F, О, Х, В, Т

F temper

Free processing state Applicable to products with no special requirements for work hardening and heat treatment conditions during the molding process, the mechanical properties of the products in this state are not specified.

О вдача

Annealed state Applicable to the processed products with minimum strength obtained by complete annealing.

H temper

the process-hardening state applies to products with increased strength through process hardening, and the products can undergo (or not) additional heat treatment to reduce the strength after process hardening.

Such as H11, H12, H13, H14, H15, H16, H17, H18, H19, H20, H21, H22, H23, H24, H25, H26, H27, H28, H29, H30, H31, H32, H33, H34, H35, H36, H37, H38, H39, H46, H48, H111, H112, H114, H116, H131, H321 тощо

H temper breakdown

HXX The first digit after state H indicates the basic treatment procedure to obtain that state, наступним чином: H1 - purely work-hardened treatment state. Applicable to the state in which the required strength is obtained by work-hardening only without additional heat treatment.

H2 - Work-hardened and non-annealed state. It is applicable to the product whose strength is reduced to the specified index by not annealing after the degree of work hardening exceeds the requirements of the finished product. For the natural aging softened alloy at room temperature, H2 and the corresponding H3 have the same smaller ultimate tensile strength value; for other alloys, H2 and the corresponding H1 have the same smaller ultimate tensile strength value, but elongation is slightly higher than H1.

H3 - work-hardened and stabilized state. The H3 state is only applicable to alloys that are gradually age-softened at room temperature (unless stabilized).

H4 - Work-hardened and painted condition. For products that have been working hardened and then lacquered resulting in no annealing.

The second digit after H indicates the degree of work hardening of the product. Кількість 8 indicates the hard state. The sum of the lesser tensile strength of the O condition and the strength difference specified in Table 2 is usually used to specify the lesser tensile strength value of HX8. For states between the O (відпалений) and HX8 states, a number from 1 до 7 should be added to the HX designator, and the number 9 should be added to HX to indicate a superhard state with a greater degree of work hardening than HX8.

W temper

Solid solution heat treatment state An unstable state, only applicable to the alloy after solution heat treatment, natural aging at room temperature, the state code only indicates that the product is in the natural aging stage.

T temper

Heat treatment state (відрізняється від Ф, О, H стан) Applicable to products that have reached stability after heat treatment, з (або без) загартовування у праці. the T designator must be followed by one or more Arabic numerals. The first digit after the T character indicates the basic type of heat treatment (від 1 до 10), and the subsequent digits indicate variations in heat treatment details. For example T0, Т2, Т3, Т4, Т5, Т6, Т7, Q8, Т24, Т32, Т35, Т73, T74, T83, T351, T354, T650, T651, T851, тощо

Surface treatment of metal aluminum alloys

За обробкою поверхні, aluminum alloy sheets can be divided into two categories: non-painted products and painted products.

1) Non-painted products

1. They can be divided into hammered aluminum sheets (without regular pattern), embossed sheets (with regular pattern), and pre-passivated aluminum oxide surface treatment sheets.
2. These products are not painted on the surface of the plate, so the appearance of the surface is not high and the price is low.

2) Painted products

(1) Класифікація.

According to the painting process can be divided into: painted board products and pre-roller coated boards.

According to the type of coating paint can be divided into: поліестер, поліуретан, polyamide, modified silicon, epoxy resin, фторуглерод, тощо.

(2) A variety of coatings, the main performance difference is the resistance to ultraviolet rays of the sun, which in the front side of the most commonly used coating is fluorocarbon paint (PVDF), its ability to resist ultraviolet light is stronger; back side can choose polyester or epoxy resin coating as a protective paint. В додаток, a layer of peel-off protective film can be applied to the front side.