金属アルミニウム合金とは?
アルミニウムは軽金属材料の 1 つであり、一定量の他の合金元素が添加されています。. アルミニウムの一般的な特性に加えて、, アルミニウム合金には、添加される合金元素の種類と量が異なるため、合金特有の特性がいくつかあります。. The density of aluminum alloy is 2.63～2.85g/cm, with high strength (σb is 110～650MPa), the specific strength is close to high alloy steel, the specific stiffness exceeds steel, with good casting performance and plastic processing performance, 良好な電気伝導性と熱伝導性, 良好な耐食性と溶接性, can be used as structural materials, in aerospace, 航空, 交通機関, 工事, mechanical and electrical, light chemical and It have a wide range of applications in aerospace, 航空, 交通機関, 工事, electromechanical, light chemical and daily necessities.
What are some common alloys of aluminum?
Metal aluminum alloy is a general term for alloys based on aluminum. There are different models, and the metal components added to various aluminum alloys are also different. The main alloying elements are Cu(銅), そして(シリコン), マグネシウム(マグネシウム), 亜鉛(亜鉛), ん( マンガン), and the secondary alloying elements are Ni(ニッケル),鉄( 鉄), の(チタン), Cr(クロム), Li(リチウム), etc.According to the alloy series, それは次のように分けることができます:
Metal aluminum alloy series
- 1000 シリーズ純アルミニウム
- 2000 シリーズ金属アルミニウム合金
- 3000 シリーズ金属アルミニウム合金
- 4000 シリーズ金属アルミニウム合金
- 5000 シリーズ金属アルミニウム合金
- 6000 シリーズ金属アルミニウム合金
- 7000 シリーズ金属アルミニウム合金
- 8000 シリーズ金属アルミニウム合金
Metal aluminum alloy raw materials are divided into
Hot selling metal aluminum alloys
1xxx series metal aluminum alloys
1xxxシリーズ:: 1050, 1060, 1070, 1100, 1200, 1235 等
3xxxシリーズ: 3003, 3004, 3005, 3104, 3105 等
5xxxシリーズ: 5005, 5052, 5083, 5086, 5454, 5754 等
6xxxシリーズ: 6061, 6063, 6082 等
Hot selling metal aluminum alloys tempers
According to temper, it can be divided into F, ○, H, W, T
F temper
Free processing state Applicable to products with no special requirements for work hardening and heat treatment conditions during the molding process, the mechanical properties of the products in this state are not specified.
ああ、気性が荒い
Annealed state Applicable to the processed products with minimum strength obtained by complete annealing.
H temper
the process-hardening state applies to products with increased strength through process hardening, and the products can undergo (or not) additional heat treatment to reduce the strength after process hardening.
Such as H11, H12, H13, H14, H15, H16, H17, H18, H19, H20, H21, H22, H23, H24, H25, H26, H27, H28, H29, H30, H31, H32, H33, H34, H35, H36, H37, H38, H39, H46, H48, H111, H112, H114, H116, H131, H321など
H temper breakdown
HXX The first digit after state H indicates the basic treatment procedure to obtain that state, 次のように: H1 - purely work-hardened treatment state. Applicable to the state in which the required strength is obtained by work-hardening only without additional heat treatment.
H2 - Work-hardened and non-annealed state. It is applicable to the product whose strength is reduced to the specified index by not annealing after the degree of work hardening exceeds the requirements of the finished product. For the natural aging softened alloy at room temperature, H2 and the corresponding H3 have the same smaller ultimate tensile strength value; for other alloys, H2 and the corresponding H1 have the same smaller ultimate tensile strength value, but elongation is slightly higher than H1.
H3 - work-hardened and stabilized state. The H3 state is only applicable to alloys that are gradually age-softened at room temperature (unless stabilized).
H4 - Work-hardened and painted condition. For products that have been working hardened and then lacquered resulting in no annealing.
The second digit after H indicates the degree of work hardening of the product. 番号 8 indicates the hard state. The sum of the lesser tensile strength of the O condition and the strength difference specified in Table 2 is usually used to specify the lesser tensile strength value of HX8. For states between the O (焼きなましされた) and HX8 states, a number from 1 に 7 should be added to the HX designator, and the number 9 should be added to HX to indicate a superhard state with a greater degree of work hardening than HX8.
W temper
Solid solution heat treatment state An unstable state, only applicable to the alloy after solution heat treatment, natural aging at room temperature, the state code only indicates that the product is in the natural aging stage.
T temper
Heat treatment state (Fとは違う, ○, H状態) Applicable to products that have reached stability after heat treatment, と (またはなしで) 加工硬化. the T designator must be followed by one or more Arabic numerals. The first digit after the T character indicates the basic type of heat treatment (から 1 に 10), and the subsequent digits indicate variations in heat treatment details. For example T0, T2, T3, T4, T5, T6, T7, Q8, T24, T32, T35, T73, T74, T83, T351, T354, T650, T651, T851, 等
Surface treatment of metal aluminum alloys
表面処理に応じて, aluminum alloy sheets can be divided into two categories: non-painted products and painted products.
1) Non-painted products
- They can be divided into hammered aluminum sheets (without regular pattern), embossed sheets (with regular pattern), and pre-passivated aluminum oxide surface treatment sheets.
- These products are not painted on the surface of the plate, so the appearance of the surface is not high and the price is low.
2) Painted products
(1) 分類.
According to the painting process can be divided into: painted board products and pre-roller coated boards.
According to the type of coating paint can be divided into: ポリエステル, ポリウレタン, polyamide, modified silicon, epoxy resin, フロロカーボン, 等.
(2) A variety of coatings, the main performance difference is the resistance to ultraviolet rays of the sun, which in the front side of the most commonly used coating is fluorocarbon paint (PVDF), its ability to resist ultraviolet light is stronger; back side can choose polyester or epoxy resin coating as a protective paint. 加えて, a layer of peel-off protective film can be applied to the front side.