What are metal aluminum alloys?

Aluminum is one of the light metal materials with a certain amount of other alloying elements added. In addition to the general characteristics of aluminum, aluminum alloys have some specific characteristics of alloys due to the different types and amounts of alloying elements added. The density of aluminum alloy is 2.63~2.85g/cm, with high strength (σb is 110~650MPa), the specific strength is close to high alloy steel, the specific stiffness exceeds steel, with good casting performance and plastic processing performance, сайн цахилгаан ба дулаан дамжуулалт, зэврэлтэнд тэсвэртэй, гагнах чадвар сайтай, can be used as structural materials, in aerospace, нисэх, тээвэрлэлт, барилга, mechanical and electrical, light chemical and It have a wide range of applications in aerospace, нисэх, тээвэрлэлт, барилга, electromechanical, light chemical and daily necessities.

What are some common alloys of aluminum?

Metal aluminum alloy is a general term for alloys based on aluminum. There are different models, and the metal components added to various aluminum alloys are also different. The main alloying elements are Cu(зэс), Тэгээд(цахиур), Mg(магни), Zn(цайр), Mn( манган), and the secondary alloying elements are Ni(никель),Fe( төмөр), -ийн(титан), Кр(хром), Li(лити), etc.According to the alloy series, гэж хувааж болно:

Metal aluminum alloy series

Metal aluminum alloy raw materials are divided into

metal aluminum plate alloy
хөнгөн цагаан хуудас хавтан
Хөнгөн цагаан ороомог
Хөнгөн цагаан ороомог
Хөнгөн цагаан тугалган цаас
Хөнгөн цагаан тугалган цаас
Хөнгөн цагаан тууз
Хөнгөн цагаан тууз

 

 

 

 

 

 

Aluminum circle disc
Aluminum circle disc
metal aluminum tread sheet
Aluminum tread sheet
metal embossed aluminum
Товойлгон хөнгөн цагаан
аноджуулсан хөнгөн цагаан
Аноджуулсан хөнгөн цагаан

 

 

 

 

 

 

толин тусгал хөнгөн цагаан
Mirror aluminum
дулаан дамжуулах хавтан
Дулаан дамжуулах хавтан
 color aluminum
Color aluminum
coated-aluminum-coil
Coated-aluminum

 

 

 

 

 

 

 

 

 

 

 

Hot selling metal aluminum alloys

1xxx series metal aluminum alloys

1xxx цуврал:: 1050, 1060, 1070, 1100, 1200, 1235 гэх мэт

3xxx цуврал: 3003, 3004, 3005, 3104, 3105 гэх мэт

5xxx цуврал: 5005, 5052, 5083, 5086, 5454, 5754 гэх мэт

6xxx цуврал: 6061, 6063, 6082 гэх мэт

Hot selling metal aluminum alloys tempers

According to temper, it can be divided into F, О, Х, В, Т

F temper

Free processing state Applicable to products with no special requirements for work hardening and heat treatment conditions during the molding process, the mechanical properties of the products in this state are not specified.

Ай уур

Annealed state Applicable to the processed products with minimum strength obtained by complete annealing.

H temper

the process-hardening state applies to products with increased strength through process hardening, and the products can undergo (or not) additional heat treatment to reduce the strength after process hardening.

Such as H11, H12, H13, H14, H15, H16, H17, H18, H19, H20, H21, H22, H23, H24, H25, H26, H27, H28, H29, H30, H31, H32, H33, H34, H35, H36, H37, H38, H39, H46, H48, H111, H112, H114, H116, H131, H321 гэх мэт

H temper breakdown

HXX The first digit after state H indicates the basic treatment procedure to obtain that state, дараах байдлаар: H1 - purely work-hardened treatment state. Applicable to the state in which the required strength is obtained by work-hardening only without additional heat treatment.

H2 - Work-hardened and non-annealed state. It is applicable to the product whose strength is reduced to the specified index by not annealing after the degree of work hardening exceeds the requirements of the finished product. For the natural aging softened alloy at room temperature, H2 and the corresponding H3 have the same smaller ultimate tensile strength value; for other alloys, H2 and the corresponding H1 have the same smaller ultimate tensile strength value, but elongation is slightly higher than H1.

H3 - work-hardened and stabilized state. The H3 state is only applicable to alloys that are gradually age-softened at room temperature (unless stabilized).

H4 - Work-hardened and painted condition. For products that have been working hardened and then lacquered resulting in no annealing.

The second digit after H indicates the degree of work hardening of the product. Тоо 8 indicates the hard state. The sum of the lesser tensile strength of the O condition and the strength difference specified in Table 2 is usually used to specify the lesser tensile strength value of HX8. For states between the O (шатаасан) and HX8 states, a number from 1 руу 7 should be added to the HX designator, and the number 9 should be added to HX to indicate a superhard state with a greater degree of work hardening than HX8.

W temper

Solid solution heat treatment state An unstable state, only applicable to the alloy after solution heat treatment, natural aging at room temperature, the state code only indicates that the product is in the natural aging stage.

T temper

Heat treatment state (Ф-ээс ялгаатай, О, H төлөв) Applicable to products that have reached stability after heat treatment, хамт (эсвэл үгүй) хатууруулах ажил. the T designator must be followed by one or more Arabic numerals. The first digit after the T character indicates the basic type of heat treatment (-аас 1 руу 10), and the subsequent digits indicate variations in heat treatment details. For example T0, T2, T3, T4, T5, T6, T7, Q8, T24, T32, T35, T73, T74, T83, T351, T354, T650, T651, T851, гэх мэт

Surface treatment of metal aluminum alloys

Гадаргуугийн боловсруулалтын дагуу, aluminum alloy sheets can be divided into two categories: non-painted products and painted products.

1) Non-painted products

  1. They can be divided into hammered aluminum sheets (without regular pattern), embossed sheets (with regular pattern), and pre-passivated aluminum oxide surface treatment sheets.
  2. These products are not painted on the surface of the plate, so the appearance of the surface is not high and the price is low.

2) Painted products

(1) Ангилал.

According to the painting process can be divided into: painted board products and pre-roller coated boards.

According to the type of coating paint can be divided into: полиэфир, полиуретан, polyamide, modified silicon, epoxy resin, fluorocarbon, гэх мэт.

(2) A variety of coatings, the main performance difference is the resistance to ultraviolet rays of the sun, which in the front side of the most commonly used coating is fluorocarbon paint (PVDF), its ability to resist ultraviolet light is stronger; back side can choose polyester or epoxy resin coating as a protective paint. Нэмж хэлэхэд, a layer of peel-off protective film can be applied to the front side.