Wholesale aluminum radiant heat transfer floor PEX spreader plate for underfloor

Aluminum heat transfer plate are installed between the floor joists to provide heat transfer across the bottom of the subfloor. The round channels formed into the aluminum snugly surround the tubing and this heat transfer from the tubing with warm water through the aluminum plates greatly increases the amount of heat that is delivered and evenly distributed throughout the floor.

Parameters of aluminum heat transfer plate

Ижил нэр: hydronic aluminum transfer plate ( самбар ), aluminum spreader plate, aluminum radiant plate, heat diffusion plate, thermal transfer plate, Aluminum heat emission fins, aluminum heat diffuser plates etc
Зузаан: 0.4мм, 0.5мм, .06мм, 0.8мм, 1.6мм гэх мэт
Өргөн: 125мм, 127мм, 128мм, 230мм, 317мм, 390мм, 610мм гэх мэт
Урт: 609мм, 1219мм, 2438мм гэх мэт
Shape: Omega

According to the grove omega shape number, гэж хувааж болно

Single grove aluminum heat transfer plate ( 1У )
Double groves aluminum heat transfer plate ( 2У )
Three groves aluminum heat transfer plate ( 3У )

Features of aluminum heat transfer plate

Omega shaped 1/2": allows you to snap in 5/8" PEX pipe during installation. This channel shape offers more contact with tubing than U-shaped plates and has a better heat transfer.

0.016 Thick Aluminum 4.5" wide

Increase Radiant Floor Heating System's efficiency and response time.
High Quality Aluminum Heat Transfer Plates for 1/2" PEX Tubing
High Quality Aluminum Plates for Fast Heat Transfer
Allow 1-2 inch spacing between plates for expansion

Comparison of floors with and without aluminum heat transfer plate

Without Aluminum heat transfer plate

Staple up without Aluminum heat transfer plate. These system will run lower than suspend tube system but hotter than plate type system due to less conductive surface.

Using Aluminum heat transfer plate

Staple up with heat transfer plates. These system will run at a lower temperature than to the addition of aluminum fins which extend the contact surface area.

Our plates are Omega-shaped (үгүй "В" эсвэл "У"-shaped like others) and allow to snap in PEX pipe during installation, making it much faster and easier. This channel shape offers more contact with tubing than U-shaped plates and has a better heat transfer.

Increase Radiant Floor Heating System's efficiency and response time.
Save time and labor - Omega-shaped plates allow for a 1-person installation.

Comfort:

Nothing comes even close to the comfort of a radiant heat system. The technology works much the same as how the sun heats your body. Heat is dispensed evenly from the floor, but does not rise because we are heating the objects in a given space, not the air. It’s a natural feel and you can enjoy a warm chair and warm floors while walking barefoot in the wintertime.

Цэвэр:

Aluminum Heat Transfer Plates systems are just about hypoallergenic. Since the air is not forced, you don’t have to be concerned about the heating system distributing pollen, dust and other allergens in the home.

Energy Efficient:

On the whole, they are more efficient than baseboard heating and forced-air heating. With forced air-heating, хүртэл 30 percent of the heat is lost due to ductwork alone. Again, hot air rises. Therfore, when heating a builing envelope with hot air, the space must be filled with hot air from the ceiling down until it reaches your actual living space. With radiant heat, the taller the ceilings, the better efficiency gains in comparison.

Whisper Quiet:

Without blowers, there are no noisy fans, and the home is peaceful.

Attractive:

This underfloor heating system eliminates inconvenient floor and wall registers.

Zoning:

Aluminum Heat Transfer Plates systems are easy to zone and offer room-to-room temperature control with multiple thermostats.

Олон талт байдал:

Aluminum Heat Transfer Plates can use a wide variety of fuel sources to heat the liquid, including solar water heaters, geothermal heat pumps, high efficiency gas boilers, wood gasification boilers or oil boilers.

The following flooring types may be installed above this type of system:

Nail-down solid hardwood
Floating hardwood
Engineered hardwood
Glue-down wood flooring
Carpet (broadloom or tiles)
Vinyl (sheet or tiles)
Ceramic tile
Ceiling
Between the floor joists to provide heat transfer across the bottom of the plywood.

Hot selling countries

Канад, Britain, Австрали, гэх мэт

Pex tubing heat transfer plates

Pex Tubing Heat Transfer Plates are formed aluminum plates specifically designed to pro- vide excellent heat transfer between radiant heating pipes and floors or other surfaces.

Pex Tubing Heat Transfer Plates are typically used when installing radiant tubing under existing floorsorin new installations with wood or other floor materials to be placed on top of the floor base. They may also be used to transfer heat to various other mechanically secure surfaces in a wall or ceiling installation.

Pex Tubing Heat Transfer Plates are a critical component of a properly designed radiant system increasing the efficiency and the reaction time of the system.

Good radiant heating is done at low water temperatures and in the case of staple-up, that means with plates.

Radiantec heat transfer plates

HEAT TRANSFER – The purpose of your radiant heating system will be to make heat in the form of warm water (in an efficient manner, we hope) and then transfer that heat to your floor. Some process must take that heat away from the tubing and apply it to the underside of the floor so that the floor can heat the area above. Aluminum is a material that transfers heat exceptionally well but it is expensive, and its use should be carefully balanced against other methods of doing the same thing, and its application should be optimized for performance and cost effectiveness.

NO ALUMINUM vs. FULL COVERAGE OF ALUMINUM – Controlled experiments have shown that covering the tubing with medium/thin gauge aluminum plates causes the system to put out about 60% more heat when operated at the same temperature.

If you use no aluminum at all, you must either raise temperature of the fluid in the tubes to a very high level, use more tubing, or both. It is not desirable to operate plastic heat exchanger tubing at high temperatures for reasons of safety, efficiency and service life.

OMEGA Heat Transfer Plates

An efficient method to distribute radiant heat from PEX tubing.

HWALU OMEGA Heat Transfer Plates offer an efficient method of distributing radiant heat from PEX tubing. Made in China from a mill finish aluminum. The channel is a wrap around omega shap (Өө) for a snug fit that holds the tubing in place very effectively in above floor systems such as the RHT Floor Panel System.

Extruded aluminum heat transfer plates

Extruded aluminum heat transfer plate for 3/8” or 1/2” PEX tubing in the same plate. DuoTrack is 48” long by 3.75” wide with pre-punched holes featuring a double groove for two sizes of PEX tubing. This reduces inventory, space and cost.

Aluminum radiant floor heat transfer plates

Aluminum radiant floor heat transfer plates are necessary for most radiant heating installations that are not encased in concrete. They improve the conductivity of heat out of the radiant tubing and increase the surface area of the system to speed heat transfer to the building.

Radiant floor heating systems like to tout that they are the "most efficient" method of heating a home. The high efficiency of radiant systems only happen due to the low required water temperatures to satisfy the heating load. So the lower the required water temperature to heat your home the more energy savings you will enjoy. The right heat transfer plate can mean money in your pocket.

Radiant heat aluminum transfer plates

Radiant Heat Transfer Plates provides 270-degree contact between the pipe and the panel, delivering higher thermal conductivity, Aluminum panels are lightweight, with an installed weight of just 1.5 lb/ft2, reducing the need for any structural reinforcements of the subfloor and increasing response time. These die-formed aluminum heat plates snap into the grid modules and help conduct heat from the tubing into the floor. Easy to install Reduces energy cost Increases comfort Convenient for use in staple up systems

Under floor radiant heat transfer plates

Aluminum Underfloor Heating Plates are used to get even heat distribution as well as reduce supply temperature by 30-40% and save on heating bills. Lower water temperature also means less damage to the flooring from excessive heat.

HWALU Aluminum Underfloor Heating Plates are formed aluminum plates specifically designed to pro- vide excellent heat transfer between radiant heating pipes and floors or other surfaces.

Aluminum Underfloor Heating Plates are typically used when installing radiant tubing under existing floorsorin new installations with wood or other floor materials to be placed on top of the floor base. They may also be used to transfer heat to various other mechanically secure surfaces in a wall or ceiling installation.

Increases heat transfer by over 30%

C-Channel design for better tubing contact and holding tubes in place

Precise thickness to optimize efficiency - thicker than the other guys!

Lower water temperatures

Lower heating bills

Great for retrofits and new construction

HWALU heat transfer plates are a critical component of a properly designed radiant system increasing the efficiency and the reaction time of the system.

Aluminum heat emission fins

Aluminum heat emission fins are used in “staple up systems” where the floor is warmed by installing tubing below the floor. Дараа нь, the heat transfer plates wrap around the tube and attach to the bottom of the floor by using a staple gun.

Aluminum heat emission fins perform three important functions:

To help to carry heat away from the tubing and distribute it through the joist space and into the floor (Heat transfer).

They support the Pex tubing.

They greatly reduce downward heat loss (backloss).

Many people ask us how the aluminum heat emission fins should be installed. To start with, you can use these rule of thumb guidelines:

If heat loss downward (backloss) is entirely wasted, cover the tubes entirely and insulate well. Unheated basements and crawl spaces are a couple of examples. If heat loss downward is useful to another space, then a reduction in aluminum by half should be considered.

The tubing should be covered entirely if the flooring material is thick or carpeted.

If low operating temperatures are desired, as for solar heating applications or for very high efficiency, cover the tubing entirely.

If there is any area that requires more heat than another (baths/greatrooms), the tubing should be covered entirely.

Best radiant heat transfer plates

Advantage Of best radiant heat transfer plates

These die-formed aluminum heat plates snap into the grid modules and help conduct heat from the tubing into the floor.

They're also used in staple-up systems to secure PEX tubing to the underside of the sub-floor to maintain contact between the tubing and the sub-floor.

Excellent way to transfer heat when used with either 1/2 in or 5/8 in PEX tubing

Суулгахад хялбар

Reduces energy cost

Increases comfort

Convenient for use in staple up systems

Applications Of Aluminum Heat Transfer Products

Under the Sub-floor installation - Between Floor Joist - Engineered Floor Boards - Between plywood installation (Sandwich Installation)

Huawei aluminum provide you best radiant heat transfer plates

hydronic heat transfer plates

hydronic heat transfer plates offer a number of advantages:

They allow for a more even heat distribution across the flooring surface if compared to staple-up tubing installation.

They serve as a support for PEX tubing and eliminate the need for additional installation accessories.

They allow for a lower fluid supply temperature, thus increasing the radiant heating system’s efficiency and reducing the costs of heating.

Stamped Heat Transfer Plates are a thinner, and are commonly used in sandwich-type radiant floors, where PEX tubing is placed between the finished floor (өөрөөр хэлбэл. laminate, hardwood, гэх мэт.) and the subfloor. These plates are wide and short, which makes them ideal for such projects and allows for more versatility in installation.

The following image illustrates the heat transfer process during joist space installation using heat transfer plates. The image speaks for itself and gives very good reasons to consider using the heat transfer plates wherever it is possible.

HWALU Radiant Aluminum Heat Plates

Radiant Aluminum Heat Plates provide 270-degree contact between the pipe and the panel, delivering higher thermal conductivity

This design results in better directional efficiency with reduced downward heat transfer

Panels are only 5/8 in. (16 мм) thick minimizing need to change construction techniques

Aluminum panels are lightweight, with an installed weight of just 1.5 lb/ft2, reducing the need for any structural reinforcements of the subfloor and increasing response time

90% lighter than a typical overpour

Radiant Aluminum Heat Plates are necessary for most radiant heating installations that are not encased in concrete. They improve the conductivity of heat out of the radiant tubing and increase the surface area of the system to speed heat transfer to the building.

Sharp	one grove
Өргөн	125мм - 610мм
Урт	заншил
Зузаан	0.4мм - 1.6мм

Sharp	double grove, two omega
Өргөн	125мм - 610мм
Зузаан	0.4мм - 1.6мм

Sharp	three grove, 3 omega
Өргөн	125мм - 610мм
Зузаан	0.4мм - 1.6мм

Дулаан дамжуулах хавтан

Дулаан дамжуулах хавтан

single grove aluminum radiant heat transfer floor spreader plate

single grove aluminum radiant heat transfer floor spreader plate

давхар төгөл хөнгөн цагаан цацраг дулаан дамжуулах шал тараагч хавтан

давхар төгөл хөнгөн цагаан цацраг дулаан дамжуулах шал тараагч хавтан

three groves aluminum radiant heat transfer floor spreader plate

three groves aluminum radiant heat transfer floor spreader plate